nf-core/eager

Edit

Introduction

Samplesheet input

You will need to create a samplesheet with information about the samples you would like to analyse before running the pipeline. Use this parameter to specify its location. It has to be a comma-separated file with 3 columns, and a header row as shown in the examples below.

--input '[path to samplesheet file]'

Multiple runs of the same sample

The sample identifiers have to be the same when you have re-sequenced the same sample more than once e.g. to increase sequencing depth. The pipeline will concatenate the raw reads before performing any downstream analysis. Below is an example for the same sample sequenced across 3 lanes:

sample,fastq_1,fastq_2
CONTROL_REP1,AEG588A1_S1_L002_R1_001.fastq.gz,AEG588A1_S1_L002_R2_001.fastq.gz
CONTROL_REP1,AEG588A1_S1_L003_R1_001.fastq.gz,AEG588A1_S1_L003_R2_001.fastq.gz
CONTROL_REP1,AEG588A1_S1_L004_R1_001.fastq.gz,AEG588A1_S1_L004_R2_001.fastq.gz

Supplying BAM input

It is possible to also supply BAM files as input to nf-core/eager. This can allow you to skip earlier steps of the pipeline (preprocessing and mapping) when desired - e.g. when re-processing public data. You can also convert input BAM files back to FASTQ files to re-undergo preprocessing and mapping. This may be desired when you want to standardise the mapping parameters between your own and previously published data.

You will still need to fill the pairment column in the input TSV sheet for the BAM files. If you do not convert the BAM files back to FASTQ, you must specify the column as single. If you do do the conversion, you must specify the type of reads the BAM file contains, i.e.:

• If the mapped reads in the BAM file are single end then specify single
• If the mapped reads in the BAM file are paired-end but merged pairs (i.e. overlapping pairs collapsed to a single read), then you must also supply single
• If the mapped reads in the BAM file are paired-end and are not merged (i.e., paired-end mapping was originally performed), then you must specify paired

Note that if you do not specify to merge BAM converted paired-end FASTQs (i.e., request paired-end mapping), only forward and reverse pairs will be used - singletons in the BAMs will be discarded!

Full samplesheet

The pipeline will auto-detect whether a sample is single- or paired-end using the information provided in the samplesheet. The samplesheet can have as many columns as you desire, however, there is a strict requirement for the first 3 columns to match those defined in the table below.

A final samplesheet file consisting of both single- and paired-end data may look something like the one below. This is for 6 samples, where TREATMENT_REP3 has been sequenced twice.

sample,fastq_1,fastq_2
CONTROL_REP1,AEG588A1_S1_L002_R1_001.fastq.gz,AEG588A1_S1_L002_R2_001.fastq.gz
CONTROL_REP2,AEG588A2_S2_L002_R1_001.fastq.gz,AEG588A2_S2_L002_R2_001.fastq.gz
CONTROL_REP3,AEG588A3_S3_L002_R1_001.fastq.gz,AEG588A3_S3_L002_R2_001.fastq.gz
TREATMENT_REP1,AEG588A4_S4_L003_R1_001.fastq.gz,
TREATMENT_REP2,AEG588A5_S5_L003_R1_001.fastq.gz,
TREATMENT_REP3,AEG588A6_S6_L003_R1_001.fastq.gz,
TREATMENT_REP3,AEG588A6_S6_L004_R1_001.fastq.gz,

An example samplesheet has been provided with the pipeline.

Reference input

nf-core/eager supports two methods of supplying reference FASTA files. The first is a direct path to a single FASTA file with optional prebuilt indicies via --fasta, --fasta_fai, --fasta_dict, etc., and the second is via a reference sheet.

Providing a reference sheet to --fasta_sheet allows users to align their input reads to multiple reference genomes in the same run. The reference sheet must be in the format of a comma- or tab-separated table, and the file extension must be csv or tsv respectively.

In addition to including the path to the FASTA, the reference sheet can also be used to specify paths to pre-built indices of each reference (namely, .fai from samtools faidx, .dict from picard CreateSequenceDictionary, and/or a directory pointing to a directory containing the indices for the given mapper - e.g. created with bwa index).

Note that passing a reference sheet to the pipeline with --fasta_sheet will override any corresponding directly-supplied parameters specifying user-build indices (--fasta_fai, --fasta_dict).

An example of a reference sheet in csv format is as follows:

reference_name,fasta,fai,dict,mapper_index,circular_target, mitochondrion_header
Mammoth_MT_Krause,//<path>/<to>/data/Mammoth_MT_Krause.fasta,/<path>/<to>/data/Mammoth_MT_Krause.fasta.fai,/<path>/<to>/data/Mammoth_MT_Krause.dict,/<path>/<to>/data/,NC_007596.2,NC_007596.2
Human_MT,/<path>/<to>/data/Human_MT.fasta.gz,,,,,

Only the reference_name, and fasta columns are mandatory, whereas all other cells can be empty depending on your context.

Files for fai, dict, mapper_index will be generated by the pipeline for you if not specified.

A real-world example could look as follows, where a user-supplied .dict file and circular_target and mitochondrion_header are not specified:

reference_name,fasta,fai,dict,mapper_index,circular_target,mitochondrion
tannerella_forsythia,/home/james/data/reference/tannerella_forstythia.fasta,/home/james/data/reference/tannerella_forstythia.fasta.fai,,/home/james/data/reference/,,

⚠️ The names of the files in the mapper_index directory must have the same basename as the FASTA itself! e.g. if FASTA is Mammoth_MT_Krause.fasta, then each BWA index file should be Mammoth_MT_Krause.fasta.<suffix>

Running the pipeline

The typical command for running the pipeline is as follows:

nextflow run nf-core/eager --input ./samplesheet.csv --outdir ./results --genome GRCh37 -profile docker

This will launch the pipeline with the docker configuration profile. See below for more information about profiles.

Note that the pipeline will create the following files in your working directory:

work                # Directory containing the nextflow working files
<OUTDIR>            # Finished results in specified location (defined with --outdir)
.nextflow_log       # Log file from Nextflow
# Other nextflow hidden files, eg. history of pipeline runs and old logs.

If you wish to repeatedly use the same parameters for multiple runs, rather than specifying each flag in the command, you can specify these in a params file.

Pipeline settings can be provided in a yaml or json file via -params-file <file>.

The above pipeline run specified with a params file in yaml format:

nextflow run nf-core/eager -profile docker -params-file params.yaml

with:

input: './samplesheet.csv'
outdir: './results/'
genome: 'GRCh37'
<...>

You can also generate such YAML/JSON files via nf-core/launch.

Updating the pipeline

When you run the above command, Nextflow automatically pulls the pipeline code from GitHub and stores it as a cached version. When running the pipeline after this, it will always use the cached version if available - even if the pipeline has been updated since. To make sure that you’re running the latest version of the pipeline, make sure that you regularly update the cached version of the pipeline:

nextflow pull nf-core/eager

Reproducibility

It is a good idea to specify the pipeline version when running the pipeline on your data. This ensures that a specific version of the pipeline code and software are used when you run your pipeline. If you keep using the same tag, you’ll be running the same version of the pipeline, even if there have been changes to the code since.

First, go to the nf-core/eager releases page and find the latest pipeline version - numeric only (eg. 1.3.1). Then specify this when running the pipeline with -r (one hyphen) - eg. -r 1.3.1. Of course, you can switch to another version by changing the number after the -r flag.

This version number will be logged in reports when you run the pipeline, so that you’ll know what you used when you look back in the future. For example, at the bottom of the MultiQC reports.

To further assist in reproducibility, you can use share and reuse parameter files to repeat pipeline runs with the same settings without having to write out a command with every single parameter.

Core Nextflow arguments

-profile

Use this parameter to choose a configuration profile. Profiles can give configuration presets for different compute environments.

Several generic profiles are bundled with the pipeline which instruct the pipeline to use software packaged using different methods (Docker, Singularity, Podman, Shifter, Charliecloud, Apptainer, Conda) - see below.

The pipeline also dynamically loads configurations from https://github.com/nf-core/configs when it runs, making multiple config profiles for various institutional clusters available at run time. For more information and to check if your system is suported, please see the nf-core/configs documentation.

Note that multiple profiles can be loaded, for example: -profile test,docker - the order of arguments is important! They are loaded in sequence, so later profiles can overwrite earlier profiles.

If -profile is not specified, the pipeline will run locally and expect all software to be installed and available on the PATH. This is not recommended, since it can lead to different results on different machines dependent on the computer environment.

• test
  • A profile with a complete configuration for automated testing
  • Includes links to test data so needs no other parameters
• docker
  • A generic configuration profile to be used with Docker
• singularity
  • A generic configuration profile to be used with Singularity
• podman
  • A generic configuration profile to be used with Podman
• shifter
  • A generic configuration profile to be used with Shifter
• charliecloud
  • A generic configuration profile to be used with Charliecloud
• apptainer
  • A generic configuration profile to be used with Apptainer
• wave
  • A generic configuration profile to enable Wave containers. Use together with one of the above (requires Nextflow 24.03.0-edge or later).
• conda
  • A generic configuration profile to be used with Conda. Please only use Conda as a last resort i.e. when it’s not possible to run the pipeline with Docker, Singularity, Podman, Shifter, Charliecloud, or Apptainer.

-resume

Specify this when restarting a pipeline. Nextflow will use cached results from any pipeline steps where the inputs are the same, continuing from where it got to previously. For input to be considered the same, not only the names must be identical but the files’ contents as well. For more info about this parameter, see this blog post.

You can also supply a run name to resume a specific run: -resume [run-name]. Use the nextflow log command to show previous run names.

-c

Specify the path to a specific config file (this is a core Nextflow command). See the nf-core website documentation for more information.

Custom configuration

Resource requests

Whilst the default requirements set within the pipeline will hopefully work for most people and with most input data, you may find that you want to customise the compute resources that the pipeline requests. Each step in the pipeline has a default set of requirements for number of CPUs, memory and time. For most of the pipeline steps, if the job exits with any of the error codes specified here it will automatically be resubmitted with higher resources request (2 x original, then 3 x original). If it still fails after the third attempt then the pipeline execution is stopped.

To change the resource requests, please see the max resources and tuning workflow resources section of the nf-core website.

Custom Containers

In some cases, you may wish to change the container or conda environment used by a pipeline steps for a particular tool. By default, nf-core pipelines use containers and software from the biocontainers or bioconda projects. However, in some cases the pipeline specified version maybe out of date.

To use a different container from the default container or conda environment specified in a pipeline, please see the updating tool versions section of the nf-core website.

Custom Tool Arguments

A pipeline might not always support every possible argument or option of a particular tool used in pipeline. Fortunately, nf-core pipelines provide some freedom to users to insert additional parameters that the pipeline does not include by default.

To learn how to provide additional arguments to a particular tool of the pipeline, please see the customising tool arguments section of the nf-core website.

nf-core/configs

In most cases, you will only need to create a custom config as a one-off but if you and others within your organisation are likely to be running nf-core pipelines regularly and need to use the same settings regularly it may be a good idea to request that your custom config file is uploaded to the nf-core/configs git repository. Before you do this please can you test that the config file works with your pipeline of choice using the -c parameter. You can then create a pull request to the nf-core/configs repository with the addition of your config file, associated documentation file (see examples in nf-core/configs/docs), and amending nfcore_custom.config to include your custom profile.

See the main Nextflow documentation for more information about creating your own configuration files.

If you have any questions or issues please send us a message on Slack on the #configs channel.

Running in the background

Nextflow handles job submissions and supervises the running jobs. The Nextflow process must run until the pipeline is finished.

The Nextflow -bg flag launches Nextflow in the background, detached from your terminal so that the workflow does not stop if you log out of your session. The logs are saved to a file.

Alternatively, you can use screen / tmux or similar tool to create a detached session which you can log back into at a later time. Some HPC setups also allow you to run nextflow within a cluster job submitted your job scheduler (from where it submits more jobs).

Nextflow memory requirements

In some cases, the Nextflow Java virtual machines can start to request a large amount of memory. We recommend adding the following line to your environment to limit this (typically in ~/.bashrc or ~./bash_profile):

NXF_OPTS='-Xms1g -Xmx4g'